TM 9-1240-335-35P
Section I. INTRODUCTION
Code
Explanation
1. Scope
X Parts and assemblies which are not procured or
This manual lists repair parts, special tools, and
stocked and the mortality of which normally is below
equipment required for the performance of direct
that of the applicable end item or component. The
support, general support, and depot maintenance of the
failure of such part or assembly should result in
Telescope M97, M97G and M97H.
retirement of the end item from the supply system.
2. General
X1 Repair parts which are not procured or stocked. The
This Repair Parts and Special Tools List is divided into
requirements for such items will be filled by use of
the following sections:
the next higher assembly or component.
X2 Repair parts which are not stocked. The indicated
maintenance category requiring such repair parts
the performance of maintenance at the direct support,
will attempt to obtain same through cannibalization.
general support, and depot level in figure and item
Where such repair parts are not obtainable through
number sequence.
cannibalization, requirements will be requisitioned,
b. Special Tools, Test and Support Equipment -
with accompanying justification, through normal
supply channels.
c. Federal Stock Number and Reference Number
G Major assemblies that are procured with PEMA funds
for initial issue only as exchange assemblies at DSU
ascending numerical sequence followed by a list of
and GSU level. These assemblies will not be
reference numbers in ascending alpha-numeric
stocked above DS and GS level or returned to depot
supply level.
sequence, cross-referenced to the illustration figure
(2) Maintenance code, indicates the lowest category
number and item number.
of maintenance authorized to install the listed item. The
3. Explanation of Columns
maintenance level codes are:
The following provides an explanation of columns in the
tabular list in Section II.
Code
Explanation
a. Source Maintenance and Recoverab ility Codes
O
Organizational maintenance
(SMR), Column 1:
F
Direct support maintenance
(1) Source code, indicates the selection
H
General support maintenance
status and source for the listed item. Source codes are:
D
Depot maintenance.
Code
Explanation
(3) Recoverability
code,
indicates
whether
P Repair parts, special tools, and test equipment which
unserviceable items should be returned for recovery or
are stocked in or supplied from the GSA/DSA, or
salvage.
Items not coded are expendable.
Army supply system and authorized for use at
Recoverability codes are:
indicated maintenance categories.
P2 Repair parts, special tools, and test equipment which
are procured and stocked for insurance purposes
Code
Explanation
because the combat or military essentiality of the
R Applied
to
repair
parts
(assemblies
and
end item dictates that a minimum quantity be
components)which are considered economically
available in the supply system.
reparable at direct and general support
P9 Assigned to items which are NSA design controlled
maintenance levels.
When the maintenance
:unique repair parts, special tools, test, measure
capability to repair these items does not exist, they
and diagnostic equipment, which are stocked and
are normally disposed of at the GS level. When
supplied by the Army COMSEC logistic system,
supply considerations dictate, some of these spare
and which are not subject to the provisions of AR
parts may be listed for automatic return to supply for
380-41.
depot level repair as set forth in AR 710-50. When
P10 Assigned to items which are NSA design controlled:
so listed, they will be replaced by supply on an
special tools, test, measuring and diagnostic
exchange basis.
equipment for COMSEC support, which are
S Repair parts and assemblies which are economically
accountable under the provision of AR 380-41,
reparable at DSU and GSU activities and which
which are stocked and supplied by the Army
normally are furnished by supply on an exchange
COMSEC logistic system.
basis. When items are determined by a GSU to be
M Repair parts which are not procured or stocked, but
uneconomically reparable, they will be evacuated to
are to be manufactured in indicated levels.
a depot for evaluation and analysis before final
A Assemblies which are not procured or stocked as
disposition.
such, but are made up of two or more units. Such
component units carry individual stock
numbers and descriptions, are procured and
stocked separately and can be assembled to
form the required assembly
at
indicated
maintenance categories.
2
