TM 9-1240-381-24&P
support equipment r e q u i r e d t o p e r f o r m t h e
maintenance authorized to perform the function
designated function.
listed in column 3. The figure represents the active
f. Column 6, Remarks. This column shwll, when
item required to perform the maintenance function
applicable, contain a letter code, in alphabetic
at the indicated level of maintenance. If the
order, which shall be keyed to the remarks con-
number or complexity of the tasks within the listed
tained in Section IV.
maintenance function vary at different main-
tenance levels, appropriate "work time" figures
B-4. Explanation of Columns in Tool and Test
will be shown for each level. The number of
Equipment Requirements, Section III.
man-hours specified by the "work time" figure
a. Column 1, Reference Code. The tool and
represents the average time required to restore an
TMDE reference code correlates with a code used
item (assembly, subassembly, component, module,
in the MAC, section II, Column 5.
end item, or system) to a serviceable condition
b. Column 2, Maintenance Level. The lowest
under typical field operating conditions. This time
level of maintenance authorized to use the tool or
includes preparation time, troubleshooting time,
test equipment.
and quality assurance/quality control time in
c. Column 3, Nomenclature. Name or iden-
addition to the time required to perform the specfic
tification of the tool or test equipment.
tasks identified for the maintenance functions
d. Column 4, National Stock Number. T h e
authorized in the maintenance allocation chart. The
National stock number of the tool or TMDE.
symbol designations for the various maintenance
e. Column 5, Tool Part Number. The manu-
levels are as follows:
facturer's part number.
...... ..
Operator
or
c rew
C.
. . .. . .. . .
B-5. Explanation of Columns in Remarks, Section
Organization a i n t e n a n c e
m
O.
IV.
F . . . . . . . . . . . . . . . . . .. Direct support maintenance
a. Reference Code. The code recorded in column
H . . . . . . . . . . . . . . . . General support maintenance
6, section II.
D . . . . . . . . . . . . . . . . . . . . . . . . .. Depot maintenance
b. Remarks. This column lists information per-
e. Column 5, Tools and Equipment. Column 5
tinent to the maintenance function being performed
specifies, by code, those common tool sets (not
--
as indicated in the MAC, section II.
individual tools) and special tools, TMDE, and
Section Il. MAINTENANCE ALLOCATION CHART
(5)
(4)
(6)
(1)
(2)
(3)
Tools
Maintenance Level
and
Group
equip-
Component/Assembly
Maintenance
c
o
Number
ment
function
F
Remarks
H
D
1
A
00
.1
Binocular, 7x50, M19 W/E
Inspect
.4
Service
.1
Repair
.5
.1
1
A
01
Binocular, 7x50, M19
Inspect
,1
Service
.4
.1
Repair
.5
.1
1
A
Inspect
.1
Eyepiece Assembly, Optical
0101
2
Service
.1
Replace
.1
1
A
Inspect
.1
0102
Objective Assembly
3,4,5
Service
.1
B
Replace
.1
Repair
.1
1
A
Inspect
0103
Housing Assembly, Optical
.1
Service
.2
Replace
.4
Repair
.1
6.7
Inspect
0104
.1
Hinge Pin Assembly
Replace
.4
.1
Inspect
02
Case, Carrying: Binocular
.1
Service
.1
Replace
.1
Repair
B-2